We supply fasteners and hardware to the following industries:
  
Aerospace
   Appliance
   Automotive
   Defense
   Naval/Maritime
   OEM
   Window and Door

Fasteners & Hardware
  Anchors
  Bolts
  Cap Screws
  Carriage Bolts
  Door Hardware
  Electronic Hardware
  Hex Bolts
  Structural Bolts
Nuts
  Finished Nuts
  Lock Nuts
  Weld Nuts
Pins
Rivets
Rods
Sc
rews
 
Clamps    
  Hangers
  Hex Head Cap Screws
  Machine Screws
  Set Screws
  Sockets
  Struts
Tapping Screws
Washers
  Bevel Washers
  Bellville Washers   
  Domed Washers
  Flat Washers
  Lock Washers
  Tooth Washers
Window Hardware
Door Hardware

Services
  Kitting / Bagging
  Private Labeling
  Stocking Programs 
    - Just-in-time
    - Kan Ban
    - Zero Inventory
    - Consignment

 

MS15795 : Mil-Spec Hardware

MS15795 : Mil-Spec Hardware Specification
Washer, Flat-Metal, Round General Purpose

MS15795 CAD DrawingClick on drawing for larger view

REQUIREMENTS:

1. MATERIAL: Corrosion resistant steel, 300 series, in accordance with procurement specification. Nickel-copper alloy, brass, copper and aluminum alloy in accordance with procurement specification.

2. PROTECTIVE COATING AND SURFACE TREATMENT: Nickel-copper alloy shall be uncoated in accordance with procurement specification. Brass shall be black oxide coated in accordance with MIL-F-495. Copper shall be uncoated in accordance with procurement specification. Aluminum alloy, anodize in accordance with MIL-A-6625, Type I or II, Class 1. Corrosion resistant steel shall be cleaned, unscaled and passivated in accordance with ASTM A380. When specified, (see Requirement 5 herein) corrosion resistant steel shall be black oxide coated in accordance with MIL-C-13924, Class 4.

3. FLATNESS: Washers shall be flat within .005 for outside diameters up to .875 inclusive and .010 for larger sizes.

4. MAGNETIC PERMEABILITY: Corrosion resistant steel washers shall have a magnetic permeability of 2.0 maximum (Air = 1.00) for a field strength of M = 200 using a magnetic indicator in accordance with MIL-I-17214.

5. PART NUMBER: The part number shall consist of the basic MS number, followed by a dash number from Tables I, II, III, IV, or V and a finish code letter “B” for black oxide corrosion resistant steel washers only. No code for all other washers.

EXAMPLE: MS15795-801B

MS15795 Basic MS Number – Dash Number
801B Finish Code Letter

MS15795-801B indicates – washer, flat-metal, round, general purpose; CRES; inside diameter .078; outside diameter .188; thickness .020; black oxide finish.

Notes:

  • 1. All dimensions are in inches.
  • 2. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence.
  • 3. Referenced government (or nongovernment) documents of the issue listed in that issue of the Department of Defense index of specifications and standards (DODISS) specified in the solicitation form a part of this standard to the extent specified herein.
  • 4. Washers represented by dash numbers 1 through 39 and 40 and 101 through 139 and 140 are cancelled after 5 December 1963. Use MS27183. Washers represented by dash numbers 201 through 239 are cancelled after 13 October 1961. Use MS27183.
  • Interchangeability Relationship. MS27183 parts can replace the cancelled washers of the same dimensions. The cancelled washers cannot always replace MS27183 washers and should be used until existing stock is depleted. Then use only the superseding MS washers of the same dimensions for design and replacement.
  • Corrosion resistant steel, 300 and 400 series, and uncoated brass washers covered by dash numbers given in previous issues or this standard are cancelled/inactivated after the indicated approval date for Revision 8. Use the new dash numbers given in the preceding sheet of this standard. The cancelled washers cannot always replace the new washers and should be used until existing stock is depleted. Then use only the new washers for design and replacement. Replacement shall be in accordance with this table.

Need the Spec?

Click here to download MS15795 Specification
(PDF Format).



Great Lakes Fasteners
2204 East Enterprise Parkway
Twinsburg, Ohio 44087

Ohio: 330-425-4488
Nationwide: 800-589-4578
Fax: 330-425-4705

ISO 9001:2015 Certified

  • Need a spec or quote?
  • It's easy-
  • call 800-589-4578
  • or fill in below

Copyright Great Lakes Fasteners, Inc. 2008

GLFTechnical Fastener Supply specializes in a wide range of industrial and military specification (MIL Spec) fasteners; including MS fasteners, AN Fasteners, and NAS Fasteners.